Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ultramid® A3HG2 - PA66-GF10 - BASF

Material Data Center offers the following functions for Ultramid® A3HG2:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Ultramid A datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caratteristiche Fisichesecco/condUnitáNorma del test
ISO Data
Indice di fusione di volume, MVR 80 / * cm³/10min ISO 1133
Temperatura 275 / * °C -
Carico 5 / * kg -
ASTM Data
Ritiro di stampaggio, parallelo 0.008 mm/mm ASTM D 955
Proprietà Meccanichesecco/condUnitáNorma del test
ISO Data
Modulo a trazione 4600 / 2600 MPa ISO 527
Carico unitario a rottura 100 / 60 MPa ISO 527
Deformazione a rottura 2.8 / 12 % ISO 527
Modulo a flessione, 23°C 4600 / - MPa ISO 178
Resistenza all'urto Charpy, +23°C 30 / 92 kJ/m² ISO 179/1eU
Resist. urto Charpy con intaglio, +23°C 7 / 9 kJ/m² ISO 179/1eA
Resistenza all'urto Izod con intaglio, +23°C - / 7 kJ/m² ISO 180/1A
ASTM Data
Resistenza alla trazione a rottura 100 / - MPa ASTM D 638
Allungamento a rottura 3 / - % ASTM D 638
Modulo a flessione 4480 / - MPa ASTM D 790
Resistenza all'urto Izod con intaglio, 1/8 in 53 / - J/m ASTM D 256
Proprietà Termichesecco/condUnitáNorma del test
ISO Data
Temperatura di fusione, 10°C/min 260 / * °C ISO 11357-1/-3
Temp.di inflessione sotto carico, 1.80 MPa 210 / * °C ISO 75-1/-2
Reaz. al fuoco spess.nom. 1.5mm HB / * class IEC 60695-11-10
Spessore provato 1.6 / * mm -
ASTM Data
DTUL a 264 psi 210 °C ASTM D 648
Temperatura di fusione 260 °C ASTM D 3418
Proprietà Elettrichesecco/condUnitáNorma del test
ISO Data
Costante dielettrica relativa, 1MHz 3.5 / 5.5 - IEC 62631-2-1
Fattore di dissipazione, 1MHz 140 / 1600 E-4 IEC 62631-2-1
Resistività volumica 1E13 / 1E10 Ohm*m IEC 62631-3-1
Resistività superficiale * / 1E10 Ohm IEC 62631-3-2
Res. Alle correnti striscianti superficiali 550 / - - IEC 60112
ASTM Data
Resistenza di volume 1E13 / - Ohm*cm ASTM D 257
Altre Proprietàsecco/condUnitáNorma del test
Assorbimento d'acqua 7 / * % Sim. alla ISO 62
Assorbimento d'umidità 2.1 / * % Sim. alla ISO 62
Massa volumica 1200 / - kg/m³ ISO 1183
Assorbimento d’acqua, equilibrio 7 % ASTM D 570
Densità 1200 kg/m³ ASTM D 792
Proprietà Specifiche Materialesecco/condUnitáNorma del test
ISO Data
Numero di viscosità 148 / * cm³/g ISO 307, 1157, 1628
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione, Altre Estrusioni
Forma fisica disponibile
Pellet
Applicazioni
Automotive, Elettrotecnica ed electrici
Disponibilità geografica
Asia Oceano Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.